Perle Systems 5500208-41 User Manual Page 83
- Page / 93
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
83
Set IOChannel
Set IOChannel Digital Output (Serial Pins)
Description Sets the Digital output for serial pins RTS and DTR. This option is only available when
the
Line Service is set to Signal I/O.
User Level Admin
Syntax
Options description
failsafe-action
mode
Set IOChannel Relay
set iochannel rts|dtr [description <string>]
[failsafe-action none|activate-outut|deactivate-output]
[mode enabled|disabled]
Provide a description of the channel, making it easier to identify. The channel
description can be up to 20 characters.
When there has been no I/O activity within the specified time (set in the Global
Settings) and the
Failsafe Timer is triggered, you can set the Failsafe Action to:
z None—The state of the Digital/Relay output remains the same, no change.
z Activate Output—Activates the output.
z Deactivate Output—Deactivates the output.
Enables the channel, allowing the settings to become active.
Description Sets the Relay output channel settings.
User Level Admin
Syntax
set iochannel <relay_number> output
[pulse continuous|counted <pulse_count>]
[active-to-inactive-delay <delay>]
[inactive-to-active-delay <delay>]
set iochannel <relay_number>
[active-signal-width <width>] [inactive-signal-width <width>]
[failsafe-action none|activate|deactivate]
Options relay_number
Specify the Relay channel number, for example, r2.
output
Specify how the channel Digital output will be handled:
z Manual—You must manually activate and deactivate the output.
z Pulse—When the output is activated, this configuration will cause the output to
pulse (go active and inactive) at a configured rate.
z Inactive-to-Active Delay—The channel output will remain inactive for the
specified time interval after it is manually started.
z Active-to-Inactive Delay—The channel output will go inactive after the specified
time interval after it is manually started.
The default is
Manual.
pulse
When the Output is Pulse, you can have it pulse in a Continuous manner or specify a
pulse
Count (each count consists of an active/inactive sequence). The default is
Continuous.
- DS1/TS2 1
- Command Line Interface 1
- Reference Guide 1
- Table of Contents 3
- About This Book 11
- Intended Audience 11
- Contacting Technical Support 12
- Repair Procedure 13
- Feedback on this Manual 13
- Introduction Chapter 1 15
- Command Shortcuts 16
- Command Options 16
- Server Commands Chapter 2 17
- Set Service 19
- Hardware Commands 20
- Modbus Commands 21
- TruePort Baud Commands 22
- IPv6 Commands 23
- Add Custom-IPv6 24
- Set Custom-IPv6 24
- Delete Custom-IPv6 25
- User Commands Chapter 3 27
- Set Termtype 28
- Set User 29
- Set User Session 29
- Show Line Users 30
- Syslog Console 30
- Show Sessions 30
- Show Termtype 30
- Configuring Users 32
- Show Default User 37
- Show User 37
- Line Commands Chapter 4 39
- Set Line Interface 44
- Set Line Service 45
- Line Commands 46
- Set Modem 47
- Line Service Commands 48
- Set Telnet-Client 49
- Set Vmodem 51
- Set Vmodem-Phone 52
- Set Modbus-Slave Line 53
- Set Modbus-Master Line 53
- Set Multihost Line 54
- Set Line Initiate-Connection 54
- Modem Commands 56
- Packet Forwarding Commands 57
- Transmit Timer 58
- Show Packet-Forwarding Line 59
- Network Commands Chapter 5 61
- Delete Community 62
- Delete Trap 62
- Set SNMP 62
- Show SNMP 62
- TFTP Commands 63
- Hosts Commands 63
- Gateway Commands 64
- Set Gateway 65
- Show Gateways 65
- Logging Commands 66
- Time Commands Chapter 6 67
- Show Date 68
- Show Time 68
- Administration 69
- Commands Chapter 7 69
- Set Bootup 70
- Show ARP 70
- Show Bootup 70
- TFTP File Transfer Commands 71
- Custom Factory Default 72
- MOTD Commands 73
- Statistic Commands Chapter 8 75
- Run-Time Statistics 76
- I/O Commands Chapter 9 77
- Set Line 78
- Set IOChannel 79
- Set IOChannel Digital Output 81
- Set IOChannel Relay 83
- Set IOChannel IOExtension 88
- Set IOChannel Multihost 90
- Show IOChannel Status 90
- Kill IOChannel 90
- Show IOChannel 91
- I/O Channel Control Commands 92
- Glossary 93
Related products and manuals for Networking Perle Systems 5500208-41
Networking Perle Systems RPS1630 User Manual
(72 pages)
(72 pages)
Networking Perle Systems 1700 User Manual
(100 pages)
(100 pages)
Networking Perle Systems Switch DS1 User Manual
(246 pages)
(246 pages)
Networking Perle Systems IOLAN SCS User Manual
(408 pages)
(408 pages)
© 2020, manymanuals.com. All rights reserved. | 0.488 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals